Sea freight

Container guide: types, sizes and weights for sea freight shipments

Container dimensions, weights and pallet capacity for every common sea container, from the 20ft and 40ft to reefer, open top and flat rack, with the values of three major carriers side by side.

23 min read

This container guide gives you the dimensions, door openings, weights and pallet capacity of every common shipping container, from the 20ft standard to the 45ft pallet wide. It also explains how to read the markings on a container door and which weight limits apply once the box leaves the terminal in Antwerp or Rotterdam on a truck.

One point first. No two container series are exactly the same. Carriers buy boxes from different manufacturers over many years, so tare weight and internal dimensions vary by a few kilograms and millimetres. The tables below show typical values from three major carriers (Hapag-Lloyd, Maersk and CMA CGM) and name the source for each figure. For your shipment, the marking on the door of the actual container is what counts.

Key figures at a glance

  • A 20ft container is 1 TEU. A 40ft container is 2 TEU (1 FEU). A 45ft container is usually counted as 2 TEU.
  • Typical capacity: 33.2 m³ (20ft), 67.7 m³ (40ft), 76.4 m³ (40ft high cube), 86 m³ (45ft high cube).
  • Typical maximum gross mass of a dry container: 30,480 kg or 32,500 kg, depending on the box.
  • Single-tier pallet capacity: 11 Euro pallets in a 20ft, up to 25 in a 40ft, 33 in a 45ft pallet wide.

Which standards define a container

Most confusion about container sizes comes from mixing up the standards. Each one has its own job.

Standard or ruleWhat it covers
ISO 668External dimensions, ratings (maximum gross mass) and minimum internal and door dimensions of series 1 containers. Current edition ISO 668:2020 with Amendment 1:2022.
ISO 1496 (parts 1 to 5)Specification and testing per container family: general cargo (part 1), thermal (part 2), tank (part 3), non-pressurised dry bulk (part 4), platform and platform-based (part 5).
ISO 6346Container number, size and type codes and the marks on the container. Current edition ISO 6346:2022; a new edition is being published by ISO at the time of writing (October 2026).
CSC (IMO, 1972)International Convention for Safe Containers: the safety approval plate and the periodic examination of containers.
SOLAS VI/2Since 1 July 2016 the shipper must provide a Verified Gross Mass (VGM) for every packed export container before it is loaded on the ship.

Every series 1 container is 2,438 mm (8 ft) wide on the outside. External lengths are 6,058 mm (20ft), 12,192 mm (40ft) and 13,716 mm (45ft). Standard height is 2,591 mm (8 ft 6 in) and high cube height is 2,896 mm (9 ft 6 in).

TEU and FEU

TEU stands for twenty-foot equivalent unit. One 20ft container equals 1 TEU, whatever its height. A 40ft container is 2 TEU, also called one FEU (forty-foot equivalent unit). Ports, carriers and statistics count capacity and volumes in TEU.

Container dimensions at a glance

Typical values across Hapag-Lloyd, Maersk and CMA CGM. Ranges show the spread between the three carriers.

TypeInternal L x W x H (mm)Door W x H (mm)Tare (kg)Max gross (kg)Capacity (m³)
20ft standard5,898 to 5,900 x 2,352 x 2,393 to 2,3952,340 x 2,280 to 2,2922,180 to 2,35030,480 (some 32,500)33.2
40ft standard12,032 to 12,034 x 2,352 x 2,393 to 2,3952,340 x 2,280 to 2,2923,630 to 3,75030,480 or 32,50067.7 to 67.8
40ft high cube12,032 to 12,034 x 2,350 to 2,352 x 2,698 to 2,7002,340 x 2,585 to 2,5973,810 to 3,90030,480 or 32,50076.3 to 76.4
45ft high cube13,556 x 2,352 x 2,698 to 2,7002,340 x 2,585 to 2,5974,700 to 4,85030,480 or 32,50086
20ft reefer5,450 to 5,456 x 2,280 to 2,294 x about 2,160 to 2,190 to load line2,290 x 2,252 to 2,2642,710 to 3,01030,480 to 32,00028.1 to 28.6
40ft high cube reefer11,584 to 11,599 x 2,290 to 2,294 x 2,425 to 2,470 to load line2,284 to 2,290 x 2,557 to 2,5674,330 to 4,70034,00067.5 to 68
20ft open top5,895 to 5,898 x 2,350 to 2,352 x 2,340 to 2,3482,338 to 2,340 x 2,2802,170 to 2,45030,480 or 32,50032 to 32.5
40ft open top12,029 to 12,032 x 2,350 to 2,352 x 2,344 to 2,3482,340 x 2,276 to 2,2803,880 to 4,05030,480 or 32,50066 to 66.8
20ft flat rackabout 5,634 to 5,638 long between corner postsopen sides2,750 to 2,90034,000 to 45,000n/a
40ft flat rack11,652 long between corner postsopen sides5,100 to 5,90052,500 to 60,000n/a

Sources: Hapag-Lloyd container pages and Container Specification booklet, Maersk equipment flyer, CMA CGM container specifications (all checked October 2026).

Standard dry containers

Dry containers (also called general purpose or GP containers) are the most common container type. They suit almost any general cargo: cartons, pallets, bags, drums, machinery parts and retail goods. They are closed, weatherproof steel boxes with doors at one end.

20ft standard container (22G1)

CarrierInternal L x W x H (mm)Door W x H (mm)Max gross (kg)Tare (kg)Max payload (kg)m³
Hapag-Lloyd5,900 x 2,352 x 2,3952,340 x 2,29230,4802,35028,13033.2
Maersk5,898 x 2,352 x 2,3932,340 x 2,28030,4802,18028,30033.2
CMA CGM5,900 x 2,352 x 2,3932,340 x 2,28030,4802,23028,25033.2

The 20ft suits heavy, dense cargo that fills the weight limit before it fills the space, such as stone, metal parts, paper rolls or bagged goods. Some series are rated at 32,500 kg gross. Hapag-Lloyd lists 20ft boxes with 30,200 kg payload at that rating.

40ft standard container (42G1)

CarrierInternal L x W x H (mm)Door W x H (mm)Max gross (kg)Tare (kg)Max payload (kg)m³
Hapag-Lloyd12,032 x 2,352 x 2,3952,340 x 2,29232,5003,75028,75067.7
Maersk12,032 x 2,352 x 2,3932,340 x 2,28032,5003,63028,87067.7
CMA CGM12,034 x 2,352 x 2,3952,340 x 2,28030,480 or 32,5003,72026,760 or 28,78067.8

A 40ft offers twice the floor length of a 20ft but hardly more payload. It is the right box for lighter, bulky cargo such as furniture, textiles, consumer goods or plastics.

40ft high cube container (45G1)

CarrierInternal L x W x H (mm)Door W x H (mm)Max gross (kg)Tare (kg)Max payload (kg)m³
Hapag-Lloyd12,032 x 2,350 x 2,7002,340 x 2,59732,5003,90028,60076.3
Maersk12,032 x 2,352 x 2,6982,340 x 2,58532,5003,81028,69076.4
CMA CGM12,034 x 2,352 x 2,7002,340 x 2,58530,480 or 32,5003,900see note76.4

The high cube is 305 mm taller than a standard box on the outside (2,896 mm instead of 2,591 mm) and gives about 8.7 m³ more space. Note: CMA CGM’s page lists the same payload for its 40ft high cube as for its 40ft standard although the high cube is 180 kg heavier, so we do not repeat that figure. Check the door of your box.

High cubes are the most common choice for volume cargo. On the road, remember that the box itself is 2.90 m tall, so the chassis must be low enough to keep the whole vehicle within the 4 m height limit in Belgium and the Netherlands.

45ft high cube container (L5G1)

CarrierInternal L x W x H (mm)Door W x H (mm)Max gross (kg)Tare (kg)Max payload (kg)m³
Hapag-Lloyd13,556 x 2,352 x 2,7002,340 x 2,59732,5004,80027,70086.0
Maersk13,556 x 2,352 x 2,6982,340 x 2,58532,5004,85027,65086
CMA CGM13,556 x 2,352 x 2,7002,340 x 2,58530,4804,70025,78086.0

The 45ft adds about 1.5 m of length to a 40ft high cube. Hapag-Lloyd builds its 45ft units with corner castings at both the 40ft and 45ft positions so they can be stacked on 40ft boxes. Within the Benelux, a truck carrying a container of up to 45ft may be up to 17.30 m long under a 2014 Benelux decision.

Pallet wide containers

A standard container is about 2,352 mm wide inside. That is enough for two Euro pallets side by side (1,600 mm) but not three (2,400 mm). Pallet wide (PW) containers solve this. Their internal width is about 2,420 to 2,444 mm, so three Euro pallets fit across.

ContainerInternal L x W x H (mm)Max gross / tare / payload (kg)m³Euro pallets (single tier)Source
40ft high cube pallet wide12,095 x 2,444 x 2,69234,000 / 4,260 / 29,74079.630CMA CGM (dims), own calculation (pallets)
45ft high cube pallet wide13,624 x 2,420 x 2,68734,000 / 4,980 / 29,02085.2533CMA CGM
45ft high cube pallet wide13,570 x 2,440 x 2,70033,000 design gross, tare 4,300 to 4,5009033 (26 pallets of 1200 x 1000 mm)DP World

Why this matters in Europe: most goods in European distribution move on Euro pallets. In a standard 45ft high cube you lose a strip of about 350 mm along one wall, so it takes 27 Euro pallets. The pallet wide version takes 33, which is 6 more pallets (about 22 %) in the same slot on the ship, the train or the truck. A tighter fit also leaves less room for the load to shift. DP World, for example, offers its 45ft pallet wide units as part of its European multimodal equipment. Availability depends on the carrier and the trade lane, so ask before you plan around one.

Special containers

Open top container (22U1, 42U1, 45U1)

An open top has rigid walls but no rigid roof. Removable roof bows and a tarpaulin close the top. You use it for cargo that is too tall for the door or that must be loaded from above by crane: machinery, steel coils, glass, stone blocks or timber. On most open tops the door header can be swung out, which makes loading through the door easier.

CarrierTypeInternal L x W x H (mm)Roof opening W x L (mm)Max gross / tare / payload (kg)m³
Hapag-Lloyd20ft5,895 x 2,350 x 2,3402,230 x 5,33832,500 / 2,450 / 30,05032.5
CMA CGM20ft5,898 x 2,352 x 2,3482,250 x 5,68230,480 / 2,200 / 28,28032
Hapag-Lloyd40ft12,029 x 2,350 x 2,3442,230 x 11,55232,500 / 4,050 / 28,45066.8
CMA CGM40ft12,032 x 2,352 x 2,3482,232 x 11,80630,480 / 3,880 / 26,60066
Hapag-Lloyd40ft high cube12,029 x 2,352 x 2,6832,192 x 11,55232,500 / 4,250 / 28,25074.9

If the cargo sticks out above the walls, it becomes out-of-gauge (OOG) cargo. Declare it at booking, because carriers handle OOG as special cargo. Maersk, for example, asks the customer to provide the tarpaulin for out-of-gauge open tops.

Flat rack and platform (22P3, 45P3)

A flat rack is a strong floor with two end walls and no side walls or roof. The flat racks in the three carrier fleets we compared have collapsible end walls (ISO type P3). Flat racks carry heavy and oversized cargo that can be loaded from the side or from above: vehicles, construction equipment, transformers, boats and steel structures.

CarrierTypeLength between corner posts (mm)Max gross / tare / payload (kg)
Hapag-Lloyd20ft5,63845,000 / 2,900 / 42,100
CMA CGM20ft5,63434,000 / 2,750 / 31,250
Hapag-Lloyd40ft high cube11,65255,000 / 5,900 / 49,100
CMA CGM40ft11,65252,500 / 5,100 / 47,400
Maersk40ft high, collapsible11,65252,500 / 5,200 / 47,300

Two rules matter. First, the full payload only applies when the weight is spread over the whole length of the side rails. A heavy, short item reduces the permitted payload, so the carrier needs the exact footprint and weight. Second, a flat rack in Hapag-Lloyd’s fleet comes without stanchions unless you ask for them at booking.

A platform is a flat rack without end walls or with the end walls folded down. Platforms carry very long or very heavy items. Hapag-Lloyd states a static load of up to 85,000 kg for its 40ft platforms when they are used as a base for break bulk cargo.

Reefer container (22R1, 45R1)

A reefer is an insulated container with a built-in refrigeration unit that cools or heats the cargo. It must be connected to a power supply to hold the temperature. Because of the insulation and the machine, a reefer has less internal space than a dry box. Cargo must not be stacked above the red load line inside, otherwise the air cannot circulate.

CarrierTypeInternal L x W (mm), height to load lineMax gross / tare / payload (kg)m³Temperature range
Hapag-Lloyd20ft5,450 x 2,280, 2,15932,000 / 2,860 / 29,14028.1down to -40 °C, up to +30 °C
Maersk20ft5,456 x 2,290, 2,18830,480 / 2,710 / 27,77028.3-30 °C to +30 °C
CMA CGM20ft5,456 x 2,294, internal height 2,27330,480 / 3,010 / 27,47028.6 (27.3 usable)usually -25 °C to +25 °C
Hapag-Lloyd40ft high cube11,599 x 2,290, 2,42534,000 / 4,420 / 29,58067.7down to -40 °C, up to +30 °C
Maersk40ft high cube11,588 x 2,290, 2,47034,000 / 4,330 / 29,67067.5-30 °C to +30 °C
CMA CGM40ft high cube11,584 x 2,294, internal height 2,55734,000 / 4,700 / 29,30068 (64.9 usable)usually -25 °C to +25 °C

The temperature range depends on the model. Maersk, for example, lists -35 °C for its Magnum reefer and -60 °C to -20 °C for its StarFreeze units. Always book the setpoint and check that the equipment offered can hold it.

Tank container (ISO tank)

A tank container is a tank held in a 20ft frame with the external dimensions of a standard 20ft container. It carries liquids such as edible oils, fruit juices, alcohols, food additives and chemicals. ISO 1496-3 also covers tanks for gases and pressurised dry bulk. CMA CGM lists 20ft tanks with 20,000 and 26,000 litres nominal capacity. Many tanks belong to leasing companies or to shippers. Some carriers, such as Hapag-Lloyd, also run their own tank fleets with separate units for foodstuffs and for chemicals.

Two filling rules from Hapag-Lloyd’s specification are worth knowing. A tank should be filled to at least 80 % to prevent dangerous surging of the liquid. It must never be filled to 100 %: there must be room for thermal expansion. Tanks also need cleaning between products. National road and rail weight limits apply to the full tank on land.

Ventilated and bulk containers

ISO 6346 has separate type codes for ventilated containers (type group V) and dry bulk containers (type group B). Both are niche equipment with limited availability. In practice many dry bulk goods such as malt, grain or plastic granules travel in a standard 20ft fitted with a liner bag. Hapag-Lloyd states that its standard 20ft boxes can be equipped with liner bags for bulk cargo. Ask for availability early if your cargo needs a specific type.

How to read the markings on a container

Container number and check digit

Every container carries a unique number under ISO 6346, marked in characters at least 100 mm high.

  • Owner code: three letters, registered with the Bureau International des Containers (BIC) in Paris. Example: CSQ.
  • Equipment category identifier: one letter. U for freight containers, J for detachable container equipment, Z for trailers and chassis.
  • Serial number: six digits chosen by the owner.
  • Check digit: one digit that lets you check whether the owner code and serial number were copied correctly.

How the check digit works, for example for CSQU 305438:

  1. Give each letter a value: A=10, B=12, C=13 and so on, skipping 11, 22 and 33. Here C=13, S=30, Q=28, U=32.
  2. Multiply each of the 10 characters by 1, 2, 4, 8, 16, 32, 64, 128, 256 and 512 in turn: 13, 60, 112, 256, 48, 0, 320, 512, 768 and 4,096.
  3. Add them up: 6,185.
  4. Divide by 11 and keep the remainder: 6,185 minus 6,182 (562 x 11) leaves 3.
  5. The check digit is 3, so the full number is CSQU 305438 3. A remainder of 10 is written as 0.

If the digit on your paperwork does not match the calculation, the number has been mistyped. Correct it before you send it to the carrier, the terminal or customs.

Size and type code

Under the container number you will see a four-character code such as 22G1 or 45G1.

PositionMeaningCommon values
1Length2 = 20ft, 4 = 40ft, L or 5 = 45ft
2Height and width2 = 8 ft 6 in high, 5 = 9 ft 6 in high (both 8 ft wide)
3 and 4TypeG1 general purpose with vents, R1 reefer, U1 open top, P3 flat rack with collapsible ends, P0 platform, T tank, B bulk, V ventilated

So 22G1 is a 20ft standard dry container, 42G1 a 40ft standard, 45G1 a 40ft high cube, 22R1 a 20ft reefer and 45R1 a 40ft high cube reefer. The 45ft high cube often shows L5G1: the letter L was the 45ft length code in the 1995 edition of ISO 6346. The current code table uses 5. ISO states that containers marked under earlier editions do not have to be re-marked, so you will see both. Pallet wide units carry a different second character, for example LEG1 for a 45ft pallet wide at DP World.

Max gross, tare and payload on the door

The doors show a weight block:

  • MAX. GROSS (maximum gross mass): the heaviest the loaded container may be, container plus cargo. This mark is mandatory under ISO 6346.
  • TARE: the weight of the empty container. Also mandatory.
  • NET or PAYLOAD: max gross minus tare, the most cargo you may load. This mark is optional, so not every box shows it.

Containers taller than 2,590 mm also carry height marks, so a high cube is easy to recognise.

The CSC safety approval plate

The CSC plate is a permanent plate of at least 200 x 100 mm, fixed at a readily visible place on the container. Under the International Convention for Safe Containers it shows:

  1. Country of approval and approval reference
  2. Date (month and year) of manufacture
  3. Manufacturer’s identification number of the container
  4. Maximum operating gross mass (kg and lbs)
  5. Allowable stacking load for 1.8 g (kg and lbs)
  6. Transverse racking test force (newtons)
  7. End-wall and side-wall strength, only if different from the standard values
  8. First maintenance examination date for new containers
  9. One-door-off stacking and racking values, only if the container is approved for that

A container must be examined within five years of manufacture and then at least every 30 months, unless the owner runs an Approved Continuous Examination Programme. In that case the plate or a mark next to it shows “ACEP”. The CSC applies to containers used in international transport. When authorities check a container under the convention, they mainly verify that it carries a valid safety approval plate.

Container weight limits: ISO rating, ship and road

Three different limits apply to the same container. The lowest one decides how much you can load.

1. The container’s own rating

The maximum gross mass on the door and the CSC plate is the absolute ceiling for that box. ISO 668 raised the standard rating for 20ft containers from 24,000 kg to 30,480 kg in 2005, the same as 40ft boxes. Many containers today are rated at 30,480 kg or 32,500 kg. Reefers are often rated at 34,000 kg and flat racks much higher. Never use a generic figure from a website: use the door marking of the box you receive.

2. The declared weight for the ship (VGM)

Before an export container is loaded, the shipper must provide its Verified Gross Mass under SOLAS. You either weigh the packed container or weigh all cargo, packaging and securing material and add the tare from the door. Our guide on pallets and cargo securing and the guide on shipping documents explain the practical side.

3. Road limits in Belgium and the Netherlands

On the road, the limit is the total weight of truck, chassis, container and cargo. This is often lower than what the container itself could carry.

Flanders (Belgium)Netherlands
Tractor and semi-trailer, standard44,000 kg with a 3-axle tractor and a 2- or 3-axle semi-trailer, explicitly also for containers up to 45ft in intermodal transport (43,000 kg with a 2-axle tractor on mechanical suspension)50,000 kg maximum combination mass, within the axle load limits (10,000 kg single axle, 11,500 kg drive axle, 24,000 to 27,000 kg on a tridem)
Higher limit with conditions48,000 kg for 3 + 3 axles with air suspension on all axles, on-board weighing, Adaptive Cruise Control, age limits and a bridge formula; up to 50,000 kg with extra allowances for alternative fuel, zero-emission drive, a retarder or a reinforced road-rail chassisn/a
Maximum height4 m4.00 m
Maximum width2.55 m (2.60 m for conditioned bodies)2.55 m (2.60 m for conditioned transport)

Sources: Flemish Codex, Royal Decree of 15 March 1968, article 32bis; RDW overview of weights and dimensions in the Netherlands, version 2025-01. Rules in Wallonia and the Brussels-Capital Region are set by those regions.

In Flanders, the 48 tonne regime only applies from 1 January 2031 to zero-emission vehicles and to alternatively fuelled vehicles first registered between 31 December 2025 and 31 December 2030. An EU revision of the weights and dimensions directive is still under negotiation at the time of writing (October 2026).

Worked example (hypothetical figures). You want to load a 40ft standard container with a tare of 3,750 kg. Suppose the haulier’s tractor and container chassis together weigh 15,000 kg. Ask your haulier for the real figure, because it varies by vehicle.

  • Flanders at 44,000 kg: 44,000 minus 15,000 leaves 29,000 kg for the container. Minus the 3,750 kg tare, about 25,250 kg of cargo can travel by road.
  • Netherlands at 50,000 kg: 50,000 minus 15,000 leaves 35,000 kg, which is more than the container’s own 32,500 kg rating. Here the container is the limit: 32,500 minus 3,750 gives 28,750 kg of cargo, provided the axle loads stay within the limits.

So the same box can legally carry several tonnes more cargo on a Dutch road than on a standard Flemish combination. If your cargo is heavy, tell your forwarder early. The route, the vehicle and the port of loading can make a real difference.

How many pallets fit in a container

The numbers below are for a single tier, pallets not overhanging, based on the internal dimensions from the carrier tables. Euro pallets measure 1,200 x 800 mm (EPAL). Industrial or “ISO” pallets in Benelux usually measure 1,200 x 1,000 mm.

ContainerEuro pallets 1,200 x 800 mmPallets 1,200 x 1,000 mmHow they are placed
20ft standard119Euro: 4 lengthwise along one wall, 7 crosswise along the other
40ft standard or high cube25 in theory, many shippers plan 23 to 2422 in theorySame pattern, 10 + 15. Only 32 mm of length to spare
45ft high cube272411 lengthwise + 16 crosswise
40ft pallet wide3024Euro: 3 across x 10 rows
45ft pallet wide3326Euro: 3 across x 11 rows

Some websites state that ten 1,200 x 1,000 mm (or 48 x 40 in) pallets fit in a 20ft. With an internal floor of about 5,898 x 2,352 mm we found no pattern for ten pallets without overhang. Plan with nine.

Check the weight as well as the space. For example, 25 Euro pallets of 1,100 kg each make 27,500 kg of cargo. That is within the payload of most 40ft boxes but well above what a standard 44 tonne combination in Flanders can carry in the hypothetical example above. Double stacking doubles the pallet count only if the goods and packaging can bear the load and the total weight stays within every limit. More on loading patterns and securing in our pallets and cargo securing guide.

How to choose the right container

Your cargoBest fitWhy
Heavy and dense (stone, steel, paper, bagged goods)20ft standardReaches the weight limit before it fills the space
Light and bulky (furniture, textiles, consumer goods)40ft high cubeMost volume per box, 76 m³
Euro pallets on European short-sea or intermodal lanes45ft pallet wide33 Euro pallets per tier instead of 27
Very large volume, not too heavy45ft high cube86 m³, if the trade lane and inland leg can handle 45ft
Taller than the door or loaded by crane from aboveOpen top (high cube version for extra height)No rigid roof, swing-out door header
Wider or longer than a container, very heavy machineryFlat rack or platformLoading from the side or top, high payload
Chilled or frozen goodsReeferControlled temperature, check the range of the model
Liquids in bulkTank container20,000 to 26,000 litres in a 20ft frame
Dry bulk (malt, granules)20ft with liner bag or a bulk containerStandard box with liner is the usual solution
Less than half a containerLCL (groupage) instead of your own boxYou pay for the space you use

Not sure? Send us the dimensions, weight and packaging of your cargo and we will propose the container and the route. See our FCL and LCL sea freight service.

Common mistakes

  • Planning with the maximum payload. The payload on the door is the container limit, not the road limit. Check the road leg first.
  • Mixing up door height and internal height. A standard 40ft is about 2,393 mm high inside but the door opening is only about 2,280 to 2,292 mm.
  • Ignoring the reefer load line. Cargo above the red line blocks the airflow and can damage the whole load.
  • Assuming every 40ft is a high cube. Book the type you need, 42G1 and 45G1 are different boxes.
  • Using the wrong standard. Dimensions and ratings come from ISO 668 and ISO 1496. Codes and marks come from ISO 6346.
  • Forgetting the vehicle height. A high cube is 2.90 m tall by itself, so the chassis deck must be low enough to keep the vehicle within the 4 m limit. Tell your haulier in advance.
  • Copying a container number without the check digit. Always check the last digit before you send it to the terminal or customs.

Glossary

  • TEU / FEU: twenty-foot / forty-foot equivalent unit.
  • High cube (HC): a container 9 ft 6 in (2,896 mm) high instead of 8 ft 6 in.
  • Tare: the weight of the empty container.
  • Max gross: the highest permitted total weight of container plus cargo.
  • Payload: max gross minus tare.
  • VGM: Verified Gross Mass, the weight declared for the ship under SOLAS.
  • CSC plate: safety approval plate under the International Convention for Safe Containers.
  • ACEP: Approved Continuous Examination Programme.
  • BIC code: the three-letter owner code registered with the Bureau International des Containers.
  • OOG: out-of-gauge, cargo that sticks out beyond the container dimensions.
  • Load line: the red line in a reefer that cargo must not exceed.
  • Gooseneck tunnel: a recess in the underside of a 40ft container so it can be carried on a gooseneck chassis.
  • SOC: shipper-owned container.

Planning a container shipment via Antwerp or Rotterdam? Your Destinex contact helps you choose the box, checks the weights for the road leg and keeps you updated until delivery. Contact us.

Source list (internal, for Destinex and Vision Lab Agency)

  1. Hapag-Lloyd, Container Specification booklet (client file 17038_Update_Container_Specification_engl_sRGB.pdf, 03/2017, PDF version 02/2020)
  2. Hapag-Lloyd container pages: hapag-lloyd.com/en/services-information/cargo-fleet/container/ (20-standard, 40-standard, 40-standard-high-cube, 45-standard-high-cube, 20-open-top, 40-open-top, 20-flatrack, 40-flatrack-high-cube, 20-reefer, 40-reefer-high-cube, 20-hardtop), checked 22.10.2026
  3. Maersk, “A handy guide to Maersk’s fleet of containers” (equipment flyer, eascpcd.maersk.com, version 09/2024); maersk.com FAQs “types and sizes of containers” and “reefer container temperature range”, checked 22.10.2026
  4. CMA CGM, cma-cgm.com/products-services/containers (dry, open top, flat rack, high cube pallet wide, tank, reefer tabs), checked 22.10.2026
  5. DP World, 45ft container (Europe equipment page), checked 22.10.2026
  6. ISO 668:2020 and ISO 668:2020/Amd 1:2022 catalogue pages (iso.org/standard/76912.html, /81611.html); ISO 668:2013 and ISO 668:1995/Amd 1:2005 previews (standards.iteh.ai)
  7. ISO catalogue ICS 55.180.10 (ISO 1496 parts 1 to 5, ISO 6346:2022, ISO 6346 edition 5 under publication: iso.org/standard/90821.html)
  8. BIC: bic-code.org/identification-number/ and /size-type-code/
  9. IMO: International Convention for Safe Containers (imo.org) and consolidated CSC text (wetten.overheid.nl/BWBV0003233/2014-07-01)
  10. IMO: Verification of the gross mass of a packed container (SOLAS VI/2)
  11. Eurostat glossary: Twenty-foot equivalent unit (TEU)
  12. EPAL: Euro pallet EPAL 1 specification (epal-pallets.org)
  13. Flemish Codex: Royal Decree of 15 March 1968, article 32bis (codex.vlaanderen.be), checked 22.10.2026
  14. RDW: Overzicht maten en gewichten in Nederland, version 2025-01 (rdw.nl)
  15. European Parliament Legislative Observatory, procedure 2023/0265(COD)

Last updated 22 October 2026

FAQ

Container guide FAQ answered by your forwarder

Short answers to the questions we hear most often on this topic.

What are the internal dimensions of a 20ft container?

A standard 20ft container measures about 5,898 to 5,900 mm long, 2,352 mm wide and 2,393 to 2,395 mm high inside. The door opening is about 2,340 mm wide and 2,280 to 2,292 mm high. Capacity is about 33.2 m³. Exact values differ slightly per carrier and container series.

What are the dimensions of a 40ft high cube container?

Inside, a 40ft high cube is about 12,032 mm long, 2,350 to 2,352 mm wide and 2,698 to 2,700 mm high, with a capacity of about 76.3 to 76.4 m³. On the outside it is 12,192 mm long, 2,438 mm wide and 2,896 mm (9 ft 6 in) high. The door opening is about 2,340 mm wide and 2,585 to 2,597 mm high.

What is the difference between a 40ft standard and a 40ft high cube?

Only the height. A high cube is 2,896 mm high outside instead of 2,591 mm, which gives about 300 mm more internal height and about 8.7 m³ more capacity. Its ISO size type code is 45G1 instead of 42G1.

What is the maximum payload of a 20ft container?

It is the maximum gross mass minus the tare, both marked on the door. For a 20ft rated at 30,480 kg, carriers list payloads of about 28,130 to 28,300 kg. Some 20ft boxes are rated at 32,500 kg. On the road, the legal vehicle weight in your country often allows less cargo than the container could carry.

How many Euro pallets fit in a 20ft and a 40ft container?

Single stacked, a 20ft takes 11 Euro pallets (1,200 x 800 mm). A 40ft takes up to 25 in theory, but with only about 3 cm of length to spare many shippers plan 23 to 24. A 45ft pallet wide takes 33.

What is a pallet wide container?

A container with an internal width of about 2.42 to 2.44 m instead of about 2.35 m. That allows three Euro pallets side by side. A 45ft pallet wide takes 33 Euro pallets per tier instead of 27 in a standard 45ft.

What does TEU mean?

TEU stands for twenty-foot equivalent unit, the volume of one 20ft container. A 40ft container is 2 TEU, also called one FEU. A 45ft container is usually counted as 2 TEU.

What do the codes 22G1 and 45G1 mean?

They are ISO 6346 size type codes. In 22G1 the first 2 means 20ft long, the second 2 means 8 ft 6 in high and G1 means general purpose container with vents. 45G1 is a 40ft (4) high cube (5) general purpose container.

What is the CSC plate on a container?

It is the safety approval plate required by the International Convention for Safe Containers. It shows the approval reference, date of manufacture, the manufacturer's identification number, the maximum operating gross mass, the allowable stacking load and the racking test force. Containers must be examined within five years of manufacture and then at least every 30 months, unless they are under an approved continuous examination programme (ACEP).

What is the difference between an open top and a flat rack?

An open top has side walls, end walls and doors but a removable tarpaulin roof, for cargo that is too tall or must be loaded by crane. A flat rack has only a floor and two end walls, for cargo that is too wide, too long or very heavy. Both are booked as special equipment.

What temperature range does a reefer container cover?

It depends on the carrier and the model. Maersk lists -30 °C to +30 °C for its standard reefers, Hapag-Lloyd states a range down to -40 °C and up to +30 °C. CMA CGM gives a usual range of -25 °C to +25 °C. Special super freezer units go down to -60 °C.

How heavy can a container truck be in Belgium and the Netherlands?

In Flanders, a tractor with a container semi-trailer may weigh 44,000 kg in total. For 6-axle combinations that meet strict technical conditions the limit is 48,000 kg (up to 50,000 kg). In the Netherlands, the maximum combination mass is 50,000 kg, within the axle load limits. The 4 m height limit applies in both countries.

Still have a question? Your contact is available 24/7.
Ready when you are

Planning your next shipment? Talk to the people who move it.

Tell us what you are shipping and where it needs to go. Your contact in Antwerp comes back to you with a clear quote and the next steps.